North Carolina Form UST-8, the Notification for Activities Involving Underground Storage Tank Systems, is the state form that every owner or operator of a regulated or commercial underground storage tank (UST) must file with the NC DEQ UST Section to report the location, ownership, construction, and leak detection details of each tank. You file it when you install new tanks, when you amend old records, or when you discover tanks that were never registered.
The form exists because state and federal law require the state to know where every petroleum and hazardous-substance tank sits, who owns it, and how it is protected from leaking. Get a field wrong and your facility permit can stall, your annual fees can be miscalculated, and your tank can lose its eligibility for the state cleanup trust funds. The current version is Revised 3/20/2018, and you should confirm that date in the footer of the copy you download before you write a single answer.
Across North Carolina there are more than 80,000 regulated USTs in the state database, and the penalty for knowingly failing to notify or for submitting false information runs as high as $10,000 per day, per violation under N.C.G.S. 143-215.94W. That single number is why this form deserves your full attention.
Here is what you will learn in this guide:
- 🛢️ How to complete every section of Form UST-8, line by line, in plain English.
- 📋 Which documents and tank records to gather before you open the form.
- 🏛️ Where to send the completed form, the fees involved, and how to keep proof of filing.
- ⚠️ The exact fields filers get wrong and the direct consequence of each mistake.
- ❓ Answers to the field-level questions that confuse owners and operators most.
What Form UST-8 Is and Who Must File It
Form UST-8 is North Carolina’s official UST notification form, required under 15A NCAC 02N .0303, which incorporates the federal notification rule at 40 CFR 280.22. The form goes to the NC Department of Environmental Quality, Division of Waste Management (DWM), UST Section, in Raleigh. Its job is to collect and update information on tank locations, ownership, construction, product stored, leak detection, and corrosion protection.
You must file UST-8 if you own or operate a UST system that was in the ground on or after May 8, 1986, unless it was taken out of operation on or before January 1, 1974. The form ties directly to the registration mandate for commercial USTs in use on or after January 1, 1989 under N.C.G.S. 143-215.94C. In 2024 the EPA granted North Carolina final approval of its UST program revisions, so the state form now satisfies both state and federal duties at once.
Covered tanks include USTs storing petroleum (motor fuels, jet fuel, waste oil, kerosene), heating oil tanks over 1,100 gallons, farm or residential tanks over 1,100 gallons, emergency generator tanks, hydraulic lift tanks, oil-water separators holding petroleum over 1% of capacity, hazardous-substance tanks over 110 gallons, airport hydrant systems, and field-constructed tanks. Excluded tanks include small home heating oil and farm tanks of 1,100 gallons or less, septic tanks, stormwater and wastewater collection systems, flow-through process tanks, and tanks that sit on or above a basement or vault floor. If your tank is excluded, you do not file, but it pays to confirm the exclusion in writing before you skip it.
The purpose, the agency, the statute, the deadline, and the penalty all connect in one chain. The purpose is an accurate state inventory. The agency, DWM, uses that inventory to issue permits and bill annual fees. The statute compels you to report. The deadline protects the state’s chance to inspect before work happens. The penalty enforces the whole system when an owner ignores it.
Before You Start: Documents and Information You Need
Filling out UST-8 from memory is the fastest way to create errors that bounce your form back. Gather these items first, because each one feeds a specific field, and a missing piece stalls the whole submittal:
- Owner legal name and mailing address. This drives Section I and must match the entity that holds title, or the state cannot bill fees correctly.
- Operator name and contact details. Section II needs this even if the operator is the same as the owner, because daily-operation responsibility is tracked separately.
- Facility name, street address, and county. Section IV ties the tanks to a physical site, and a wrong county routes your form to the wrong regional office.
- Facility ID number, if one already exists. Listing it in Section IV prevents the state from opening a duplicate record for a site you already have.
- Tank installation dates, manufacturers, and models. Section VI.A. cannot be processed without these, and guessing the date can change which rules apply to your tank.
- Tank capacity and product stored for each tank. These set your annual fee and your leak detection duties, so an error here costs money or compliance.
- Leak detection and corrosion protection method records. Sections VI.D. and VI.E. require the equipment make, model, and start date, which usually come from your installation contractor’s closeout package.
- Spill and overfill equipment details. Section VI.G. needs the type, manufacturer, model, and install date, missing from many older files but required all the same.
- Proof of financial responsibility. Section VIII needs your insurance policy number, insurer, and coverage dates, or a note that you already filed a Certification of Financial Responsibility.
- A check payable to DEQ-UST if you are reporting tanks not previously registered, since annual operating fees may be due with the form.
If any item is missing, do not leave the field blank and hope. Call the UST Section at (919) 707-8171 to confirm what to enter, because a blank required field is treated as an incomplete submittal and delays your permit.
Where to Get the Form and How to Access It
You download Form UST-8 free of charge as a fillable PDF directly from the NC DEQ UST forms page. The rule 15A NCAC 02N .0303 names this exact form and confirms it is provided by the Division at no cost. Never pay a third-party website for a “premium” copy, because the state version is always free and always current.
Open the PDF in Adobe Acrobat Reader rather than a web browser preview, because browser viewers often fail to save your typed entries. Type or print every item except the signature, which must be handwritten in ink. The form is six pages long, and if you own more than four UST systems at one facility, you photocopy the additional description sheets and staple them to the form.
Always check the footer for Revised 3/20/2018 before you start. The state periodically updates UST forms, and submitting an outdated version is a common reason a package is returned. If the date you see is older, download a fresh copy from the official page.
Step-by-Step: How to Fill Out Form UST-8 Line by Line
Complete Sections I through VI.A. and IX in full. Then complete only the applicable parts of Sections VI.B. through VIII. The instructions on the form itself spell out this order, and following it keeps you from filling boxes that do not apply to your tanks.
Section I — Ownership of UST System
This section asks who legally owns the tank system. Enter the owner’s full legal name exactly as it appears on corporate or property records, then the contact name (if different), street address, city, state, ZIP, county, phone, fax, and email. A named example: Coastal Fuel Mart, LLC enters its registered LLC name, not the trade name on the sign out front. The most common edge case is a tank owned by a corporation but operated by a franchisee, in which case the corporation goes here and the franchisee goes in Section II.
A common mistake is entering the gas station’s brand name instead of the legal entity that holds title. The direct consequence is that annual operating fee invoices go to a name that does not match state corporate records, and payments get misapplied. A misconception filers carry is that “owner” means whoever runs the store; in this form, owner means whoever owns the tank system, which is often the property owner or a leasing company.
Check the box “Real Property Owner of Site” if the owner here also owns the land. Also check the boxes describing the type of UST owner: State Gov’t, Local Gov’t, Private/Corporate, or Federal Gov’t, and enter a GSA Facility ID if federal. Federal and state governments owning regulated petroleum USTs are exempt from the financial responsibility funding, so this checkbox affects Section VIII later.
Section II — Operator of UST System
This section asks who controls the daily operation of the tank. If the operator is the same person or company as the owner, check the box “Check if same as owner” and you may skip the repeated fields. Otherwise enter the operator’s legal name, contact, address, and phone exactly as in Section I. A named example: Maria Delgado, who runs the day-to-day fueling business as a franchisee, is the operator, while the property company is the owner.
The most common edge case is a property management firm that owns tanks leased to a separate fuel retailer. The retailer is the operator and must appear here. A common mistake is leaving this section blank when the operator differs from the owner, which the state reads as missing data and the form gets returned. A misconception is that the operator field is optional; it is not, because operator-class certification and fee responsibility track to this name.
Section III — Type of Notification
This section asks why you are filing. Check all that apply: Amendment of a previous registration form, Temporary closure, Existing Facility with UST system not previously registered, or Change of Ownership. If you check “Amendment,” you complete only the items that changed from a prior UST-6 or UST-8 submittal. A named example: Coastal Fuel Mart checks Amendment because it only swapped a leak detection console and nothing else changed.
The most important edge case is “Change of Ownership,” which requires you to attach Form UST-15 along with copies of the legal transfer documents such as a bill of sale or property deed. The form warns in plain text that failure to complete a UST-15 results in no effective change of ownership status. A common mistake is checking “Existing Facility not previously registered” without enclosing the fee check, which delays processing. A misconception is that checking “Amendment” lets you redo the whole form; it does not, you report only the changed items.
Section IV — Location of UST System
This section asks where the tanks physically sit. Enter the facility name, street address, city, ZIP, county, phone, and the County Tax Map Number. State the number of regulated tanks and the total number of tanks at this location, and answer whether any UST is within 500 feet of a water supply well. A named example: Coastal Fuel Mart enters 4 regulated tanks and 5 total because one tank is an excluded small heating oil tank.
The key edge case is the water-supply-well question, because a “Yes” here triggers stricter interstitial monitoring requirements under the leak detection rules. A common mistake is leaving the Facility ID blank when one already exists, which spawns a duplicate site record and double billing. A misconception is that “location” is the same as the mailing address in Section I; the facility location must be the actual ground where tanks are buried, even if mail goes elsewhere. Check the Indian-lands box only if the tanks sit on a reservation or other Indian lands.
Section V — Contact Person for UST Location
This section asks for a live human at the site. Enter the contact name, job title, and phone number. A named example: James Carter, Store Manager, (910) 555-0148 is the person inspectors call when they need site access.
The common edge case is an unstaffed site such as an emergency generator tank at a cell tower, where you list the facilities manager who holds the keys. A common mistake is listing a corporate switchboard with no direct extension, which delays inspections when staff cannot reach anyone. A misconception is that this must be the owner; it should be whoever can actually open the gate and answer questions on site.
Section VI.A. — UST Information (Tank Description)
This is the heart of the form. For each tank, enter a Tank/Compartment ID (A, B, C or 1, 2, 3; for compartments 1A, 1B), date of installation, tank manufacturer, tank model, and materials of construction using the coded choices in footnote 1, such as DW Steel/FRP (e.g., ACT-100). Then enter capacity in gallons, whether the tank is siphon manifolded (and to which tank), and the product stored using the footnote 2 list, such as Gasoline, Diesel, or Hazardous Substance. A named example: Marcus Webb enters Tank 1, installed 03/15/2019, Containment Solutions, DW FRP, 10,000 gallons, product Gasoline.
The materials-of-construction codes are the field filers misread most, because they must pick from an exact list of double-walled and single-walled options rather than writing free text. The edge case is a compartment tank, where you list each compartment size separately under its own ID. A common mistake is entering a rounded or “nominal” capacity instead of the actual gallon capacity, which throws off your annual fee calculation. A misconception is that “product stored” can be a brand name; it must be one of the listed categories, and a hazardous substance also requires its Chemical Abstract Service (CAS) number.
Section VI.B. — Piping System
This section describes the piping connected to each tank. Enter piping manufacturer, model, material of construction from the footnote choices (such as DW Flex or SW Steel), whether it is an airport hydrant system, the piping configuration (Pressurized, Suction, European Suction, or Gravity), and, if suction, where the check valve sits (Tank, Dispenser, or Both). A named example: Marcus Webb enters DW Flex (e.g., APT XP), configuration Pressurized.
The edge case is European suction piping, which is exempt from line leak detection under the rules and changes how you answer Section VI.D. A common mistake is marking piping “Pressurized” when it is actually suction, because pressurized lines legally require an automatic line leak detector and suction lines may not. A misconception is that piping material does not matter; it directly determines your corrosion protection and leak detection duties.
Section VI.C. — Under Dispenser Containment (UDC)
This section asks about containment under each fuel dispenser. Enter the dispenser numbers, UDC manufacturer, model, whether it is single (SW) or double walled (DW), the method of monitoring (Sump Sensor, Vacuum, Pressure, Hydrostatic, or None), and the material. If all dispensers share the same UDC, enter ALL in column 1 and complete only that column. A named example: Marcus Webb enters ALL, OPW, DW, monitoring Sump Sensor.
The edge case is a site with mixed dispenser models, where each model gets its own column with the dispenser numbers it covers. A common mistake is entering individual dispenser numbers in every column when one ALL entry would have been correct, creating needless clutter and confusion. A misconception is that UDC is optional for older sites; containment is required for dispensers installed under the current rules, and omitting it flags a compliance gap.
Section VI.D. — Leak Detection
This section captures how each tank and its piping are monitored for leaks. Check every method that applies for both Tank and Piping columns, such as Automatic tank gauging, Interstitial monitoring, Statistical inventory reconciliation, or Automatic line leak detector. Then enter the date the method was initiated, the monitoring console manufacturer and model, and the interstitial sensor makes and models. A named example: Marcus Webb checks Interstitial monitoring for both tank and piping and enters console Veeder-Root TLS-450.
The big edge case is that interstitial monitoring is required for all systems installed on or after 11/1/2007, and for any system near a public water supply well or protected surface water, so a tank that qualifies must show this method. A common mistake is checking a method the equipment cannot actually perform, like manual tank gauging on a 12,000-gallon tank, when that method is valid only for tanks of 550 gallons or less (or 551 to 1,000 gallons with specific diameters). A misconception is that one leak detection method covers both tank and piping; the form deliberately separates them because piping usually needs its own line leak detector.
Section VI.E. — Corrosion Protection
This section asks how metal tanks and piping are protected from rust. Check the methods that apply, such as Sacrificial anodes, Impressed current, Fiberglass Reinforced Plastic (FRP), Steel/FRP Composite, or Internal lining, and enter the date that method was installed. A named example: a steel tank from Tidewater Oil Co. shows Impressed current with an install date of 06/2005.
The edge case is a fiberglass or jacketed tank that needs no cathodic protection, where you check FRP or the matching non-metal option rather than leaving the section blank. A common mistake is checking None for a bare steel tank, which signals an out-of-compliance system that invites an enforcement action. A misconception is that corrosion protection applies only to tanks; the form tracks piping separately because steel piping rusts just as fast.
Section VI.F. — Flexible Connectors, Submersible Pumps, and Riser Pipes
This section asks whether buried metal fittings are isolated from the ground. For each tank, answer Yes or No to whether a flex connector is present, whether it is isolated from the ground, whether the submersible pump (on pressurized piping) is isolated, and whether riser pipes and metal fittings are isolated. If “No,” enter the cathodic protection method: IC (Impressed Current), SA (Sacrificial Anode), or N (None). A named example: Tidewater Oil Co. enters flex connector Yes, isolated No, method SA.
The edge case is a site that has plastic risers and no metal fittings, where the honest answer is that isolation does not apply because there is no bare metal. A common mistake is answering “No” to isolation and then leaving the cathodic protection code blank, which the state reads as an unprotected metal component. A misconception is that this tiny-looking section is unimportant; unprotected metal fittings are a frequent source of leaks and inspectors check them closely.
Section VI.G. — Spill/Overfill Protection
This section documents how the tank prevents spills during delivery. Enter the Spill Prevention Equipment Type (Catchment Basin, None, or Not Required), its manufacturer, model, the interstice monitoring method if double-walled, and the install date. Then enter the Overfill Prevention Equipment Type (Automatic shutoff, Alarm at tank, Ball float, None, or Not Required), manufacturer, model, and install date. A named example: Coastal Fuel Mart enters Catchment Basin, OPW, and overfill Automatic shutoff.
The edge case is a tank always filled by transfers of 25 gallons or less, where “Not Required” is a valid entry for spill or overfill equipment. A common mistake is entering Ball float for a tank installed after June 1, 2017, when new ball float vent valves can no longer be installed under 15A NCAC 2N .0301. A misconception is that overfill protection is optional on small tanks; it is required unless the tank meets the narrow 25-gallon transfer exemption.
Section VI.H. — Stage I Vapor Recovery (Gasoline USTs Only)
This section applies only to gasoline tanks. Enter the combined annual throughput in gallons, check whether the system is Coaxial or Dual point, or check that vapor recovery is not required, and enter the install date. A named example: Coastal Fuel Mart enters throughput 320,000 gallons and checks Dual point.
The edge case is the exemption: vapor recovery is not required for gasoline tanks of 550 gallons or less, tanks of 2,000 gallons or less installed before July 1, 1979, or facilities with combined annual throughput under 50,000 gallons. A common mistake is leaving this blank for a busy gasoline site, when Stage I recovery is mandatory above the throughput threshold. A misconception is that diesel tanks need this section; it is for gasoline only.
Section VII — Out of Operation UST Systems
This section reports tanks that are closed or idle. Enter the date a tank was permanently closed (removed or filled with inert material), the date temporary closure began, and the date it ended. A named example: Tidewater Oil Co. enters a temporary closure begin date of 01/10/2026 for a tank pulled from service during a remodel.
The edge case is that permanent closure requires the separate Form UST-3 filed at least 30 days before the work, so UST-8 alone is not enough to close a tank for good. A common mistake is using temporary closure to park a tank indefinitely, when state rules cap how long a tank may stay in temporary closure before it must be permanently closed. A misconception is that an idle tank needs no reporting; an unreported out-of-service tank still accrues compliance duties.
Section VIII — Financial Responsibility (Regulated Petroleum USTs Only)
This section proves you can pay for cleanup if a tank leaks. Indicate whether the tank owner or operator is providing financial responsibility, then check the mechanisms that apply, such as Self-insurance, Corporate guarantee, Insurance and risk retention group coverage, Surety bond, Letter of Credit, or Insurance pools, and enter the policy number, insurer, and period of coverage. A named example: Coastal Fuel Mart checks Insurance, enters policy UST-44821, insurer Federated, and coverage dates.
The required additional amount is the sum of the “3rd Party ($100,000.00)” and “Cleanup ($20,000.00)” State Trust Fund deductibles plus $600 per tank as a scaling factor, and the trust funds cannot cover those deductibles. The edge case is a government owner: federal and state governments owning regulated petroleum USTs are exempt and check accordingly. A common mistake is checking “I have previously submitted proof” when coverage has actually lapsed, which is a false certification. A misconception is that paying annual operating fees alone fully satisfies financial responsibility; the fees cover a major portion, but you must assure the deductible amounts separately.
Section IX — Certification and Acknowledgement
This is the legal signature block, completed after Sections I through VII. Read the certification, then print the name and title of the owner or authorized representative, sign in ink, and date it. If the operator provides financial responsibility, the operator signs the second block. A named example: Marcus Webb, President, signs and dates 05/30/2026.
The certification states, under penalty of law, that you examined the information and believe it true, accurate, and complete, and that all applicable state and federal UST requirements have been met. The edge case is signing as an officer, agent, estate administrator, or under power of attorney, which requires you to attach a copy of the legal document proving you can sign in that capacity. A common mistake is typing the signature instead of signing in ink, which voids the certification. A misconception is that this is a routine formality; it is a sworn statement, and a false certification triggers the $10,000-per-day penalty under N.C.G.S. 143-215.94W.
Three Filled-Out Examples Using Real Scenarios
Each scenario below follows one named filer through the form so you can see what real entries look like.
Scenario 1: Marcus Webb Installs New Tanks at a New Convenience Store
Marcus is opening a new fuel station and is notifying for two newly installed double-walled tanks.
| Form Section | What Marcus Enters |
|---|---|
| I. Ownership | Webb Retail Group, LLC, full mailing address, Private/Corporate checked |
| II. Operator | “Same as owner” box checked |
| III. Type of Notification | Existing Facility not previously registered is NOT checked; this is a new install via UST-6, so UST-8 documents the system |
| IV. Location | Webb Express #1, 4 regulated tanks, 4 total, water-supply-well No |
| VI.A. Tank Info | Tank 1, installed 03/15/2026, Containment Solutions, DW FRP, 10,000 gal, Gasoline |
| VI.D. Leak Detection | Interstitial monitoring checked for tank and piping, console Veeder-Root TLS-450 |
| VI.G. Spill/Overfill | Spill Catchment Basin, overfill Automatic shutoff |
| VIII. Financial Responsibility | Insurance, policy UST-44821, insurer Federated |
| IX. Certification | Marcus Webb, President, signed in ink, 05/30/2026 |
Scenario 2: Tidewater Oil Co. Amends Records After a Leak Detection Upgrade
Tidewater swapped out an aging monitoring console and is reporting only that change.
| Form Section | What Tidewater Enters |
|---|---|
| I. Ownership | Tidewater Oil Co., Inc., address, Private/Corporate |
| III. Type of Notification | Amendment of a previous registration form checked |
| IV. Location | Tidewater Marina Fuel, existing Facility ID listed |
| VI.D. Leak Detection | New console Veeder-Root TLS-350, date initiated 04/2026 |
| VI.E. Corrosion Protection | Impressed current, unchanged, install date 06/2005 |
| VI.F. Fittings | Flex connector Yes, isolated No, method SA |
| VII. Out of Operation | Left blank, no tanks closed |
| VIII. Financial Responsibility | “Previously submitted, no changes” box checked |
| IX. Certification | Helen Brooks, Vice President, signed, 04/22/2026 |
Scenario 3: Coastal Fuel Mart Registers Tanks That Were Never Reported
Coastal bought a property and found three buried tanks missing from state records.
| Form Section | What Coastal Enters |
|---|---|
| I. Ownership | Coastal Fuel Mart, LLC, address, Real Property Owner checked |
| III. Type of Notification | Existing Facility with UST system not previously registered checked |
| IV. Location | Coastal Fuel Mart #3, 3 regulated tanks, water-supply-well Yes |
| VI.A. Tank Info | Tank A, installed 1998 (from records), Steel, 8,000 gal, Diesel |
| VI.D. Leak Detection | Automatic tank gauging plus Interstitial monitoring (well within 500 ft) |
| VI.H. Vapor Recovery | Throughput 320,000 gal, Dual point |
| VIII. Financial Responsibility | Insurance, policy UST-90233 |
| IX. Certification | Dana Rivera, Manager, signed, 05/28/2026 |
| Payment | Check payable to DEQ-UST for annual operating fees enclosed |
How to File the Completed Form UST-8
North Carolina accepts UST-8 by mail, fax, and email, and you should keep proof no matter which channel you use.
- By mail: Send the signed original to NC DEQ / DWM / UST Section, 1646 Mail Service Center, Raleigh, NC 27699-1646, ATTN: Registration & Permitting. There is no filing fee for the notification itself, but annual operating fees may be due for tanks not previously registered. Pay by check made payable to DEQ-UST and enclose it with the form. Processing typically takes several weeks; keep a certified-mail receipt as your proof of filing.
- By fax: Send to (919) 715-1117. Fax works for amendments and updates, but you cannot fax a fee check, so a newly registered tank still needs a mailed payment. Keep the fax transmission confirmation as proof.
- By email: Send a scanned, signed PDF to UST.Permits@deq.nc.gov. Email is convenient for amendments; keep the sent message and any reply as proof. For questions on fee amounts, call the UST Section at (919) 707-8171 before you send payment.
If you are reporting tanks not previously registered, call (919) 707-8171 first to learn the exact fee, because mailing the wrong amount delays the registration. Always photocopy the entire signed package before sending, so you hold an identical record of what the state received.
What Happens After You File
After DWM receives your UST-8, the Registration and Permitting unit reviews it, assigns or confirms a Facility ID and tank ID numbers, and enters the data into the state UST database. If anything is incomplete, staff contact your Section V site contact or the owner to request the missing information, which is why accurate contact fields matter so much.
Once the record is complete and fees are current, the facility moves toward an operating permit and is placed on the annual operating fee billing cycle under N.C.G.S. 143-215.94C. For newly registered or newly installed tanks, an inspector may schedule a compliance inspection to verify the equipment you described. Keep your stamped copy and any correspondence, because the state’s record and yours should always match.
If you filed an amendment, the database is updated to reflect only the changed items, and your prior data stays in place. If you reported a change of ownership, the transfer is not recognized until the accompanying Form UST-15 and legal documents are accepted, so follow up if you do not receive confirmation.
Mistakes to Avoid When Filling Out Form UST-8
- Entering the trade name instead of the legal owner in Section I; fee invoices then go to a name that does not match records.
- Leaving Section II blank when the operator differs from the owner; the state treats it as missing data and returns the form.
- Forgetting to attach Form UST-15 on a change of ownership; the ownership change has no legal effect.
- Omitting the Facility ID in Section IV when one exists; the state opens a duplicate record and double-bills you.
- Answering the water-supply-well question wrong; a wrong “No” can hide a mandatory interstitial monitoring duty.
- Writing free text for materials of construction instead of the coded choices; the entry cannot be processed cleanly.
- Reporting nominal instead of actual tank capacity; your annual fee is miscalculated.
- Checking a leak detection method the equipment cannot perform; it flags a compliance contradiction.
- Marking None for corrosion protection on bare steel; it signals an out-of-compliance tank and invites enforcement.
- Entering Ball float overfill for a tank installed after June 1, 2017; that device can no longer be installed.
- Typing the signature instead of signing in ink; the certification is void.
- Mailing the wrong fee amount for unregistered tanks; the registration stalls until payment is corrected.
Dos and Don’ts
Do:
- Download a fresh copy and confirm Revised 3/20/2018 in the footer, because outdated forms get returned.
- Use the exact coded entries from the form’s footnotes, since the state database reads only those codes.
- Photocopy the full signed package before sending, so you can prove what you filed.
- Call (919) 707-8171 to confirm fees before mailing a check, to avoid a payment mismatch.
- Match the owner name to corporate or property records, so fee billing lands correctly.
- List existing Facility and tank IDs, to prevent duplicate records.
Don’t:
- Don’t guess installation dates, because the date determines which rules apply to the tank.
- Don’t leave required fields blank, since a blank required field is an incomplete submittal.
- Don’t pay a third-party site for the form, because the official version is always free.
- Don’t use UST-8 alone to permanently close a tank, since that needs Form UST-3 thirty days ahead.
- Don’t certify “no changes” to financial responsibility if coverage lapsed, because that is a false statement.
- Don’t fax a fee check, since faxed payments cannot be processed.
Pros and Cons of Filing UST-8 on Your Own vs. With a Consultant
| Filing on Your Own | Filing With a UST Consultant |
|---|---|
| No consultant fee, so the lowest out-of-pocket cost | Professional fee, but fewer rejected submittals |
| Full control over timing and contact details | Consultant tracks deadlines and the 30-day notice rules |
| Direct knowledge of your own ownership records | Expertise in coded equipment entries that owners misread |
| Works well for simple amendments | Strong fit for new installs with complex leak detection |
| Risk of misreading construction or leak detection codes | Lower risk of the $10,000-per-day false-certification penalty |
Key Entities and Related Forms
Several agencies, statutes, and forms interact with UST-8, and knowing each role helps you file correctly. The NC DEQ Division of Waste Management, UST Section is the agency that receives the form, issues permits, and bills fees. The federal rule 40 CFR 280.22 sets the baseline notification duty, while the state rule 15A NCAC 02N .0303 adapts it for North Carolina. The penalty statute N.C.G.S. 143-215.94W enforces honest reporting.
Related forms include UST-6, the application to install or replace a tank; UST-3, the notice of intent for permanent closure or change-in-service filed at least 30 days ahead; and UST-15, the change-of-ownership form that must accompany UST-8 when title transfers. The EPA’s 2024 final approval of North Carolina’s program means the state form now carries federal weight, so filing UST-8 correctly satisfies both governments at once.
FAQs
Is there a fee to file Form UST-8?
No. The notification form itself has no filing fee, but annual operating fees may be due for tanks not previously registered, and you must enclose a check payable to DEQ-UST.
Do I have to file UST-8 at least 30 days before installing a leak detection device?
Yes. Under 15A NCAC 02N .0303, notice for an external leak detection device, such as vapor or groundwater monitoring, must be given at least 30 days before the activity begins.
In Section I, do I write the gas station’s brand name or the legal owner name?
No, not the brand name. Enter the legal entity that owns the tank system, such as the LLC or corporation on title, so fee invoices match state records.
In Section VI.A., can I write the product brand name in “Product stored”?
No. You must select a listed category like Gasoline, Diesel, or Hazardous Substance, and a hazardous substance also requires its Chemical Abstract Service (CAS) number.
Do I check “same as owner” in Section II if my company both owns and runs the tanks?
Yes. Check the “same as owner” box and you may skip the repeated operator fields, which prevents duplicate and conflicting entries.
In Section VI.A., should I enter nominal or actual tank capacity?
No, not nominal. Enter the actual gallon capacity, because the state uses it to calculate your annual operating fee, and a rounded number creates billing errors.
Can I use Form UST-8 to permanently close a tank?
No. Permanent closure requires Form UST-3, filed at least 30 days before the work; UST-8 Section VII only records the dates after a closure.
Do federal and state government tank owners complete Section VIII?
No. Federal and state governments owning regulated petroleum USTs are exempt from the financial responsibility funding requirement and indicate that exemption.
Is a typed signature acceptable in Section IX?
No. The form requires every item typed or printed except the signature, which must be signed in ink, or the certification is void.
Do I need to attach anything when I check “Change of Ownership” in Section III?
Yes. You must attach Form UST-15 plus copies of legal transfer documents such as a bill of sale or deed, or the ownership change has no effect.
Does answering “Yes” to the water-supply-well question in Section IV change my duties?
Yes. A tank within 500 feet of a water supply well generally triggers mandatory interstitial monitoring leak detection under the state rules.
Can I still enter “Ball float” for overfill protection?
No, not for tanks installed after June 1, 2017. New ball float vent valves cannot be installed under 15A NCAC 2N .0301, so a newer tank needs automatic shutoff or an alarm.
What is the penalty for filing false information on UST-8?
Yes, there is a serious one. Under N.C.G.S. 143-215.94W, knowingly failing to notify or submitting false information carries a civil penalty up to $10,000 per day, per violation.
Where do I mail the completed Form UST-8?
Yes, there is one address. Mail the signed form to NC DEQ / DWM / UST Section, 1646 Mail Service Center, Raleigh, NC 27699-1646, ATTN: Registration & Permitting.
Related reading
- How to Fill Out Florida DEP Underground Storage Tank Registration + FAQs
- How to Fill Out Illinois IEPA Underground Storage Tank Registration + FAQs
- How to Fill Out the Pennsylvania DEP Underground Storage Tank Registration Form
- How to Fill Out the Georgia EPD Underground Storage Tank Notification Form (Form 7530) + FAQs
- How to Fill Out the Underground Storage Tank Closure Report + FAQs
- How to Fill Out Virginia VA DEQ Underground Storage Tank Notification (Form 7530-3) + FAQs
- How to Fill Out the Washington Ecology Water Quality Modification Permit + FAQs